With over 17 years of IT hardware supply chain resources




Intel Skylake SP Microarchitecture Changes

In this piece, we are going to go a bit deeper in the microarchitecture features of the new Intel Xeon Scalable Processor Family. We are doing extensive coverage of the Intel Xeon Scalable Processor Family Launch including platform level, chipsets, mesh interconnects, benchmarks, vendor launches, and SKU stacks. Check out our Intel Xeon Scalable Processor Family Launch Coverage Central for more information. Since the new processors are a huge piece of text to keep writing out, you may see us use the official codename of Skylake-SP in this article. e3-1515m v5

We are going to focus this piece specifically on Skylake core architecture and one of the major new instructions, AVX-512.

Starting with a Skylake Core

We start the microarchitecture discussion with the basic Skylake-SP core. What may surprise some readers is that this is essentially a basic Skylake core that we have seen Intel use for years, and then add additional L2 cache and an additional FMA and AVX execution unit bolted on.

Intel Skylake SP Microarchitecture Core Cache AVX

Not all chips will have the second FMA unit. That is another part of the differentiation between the various processor tiers.

Here is the slide that describes some of the more technical microarchitecture improvements over Broadwell-EP.

Intel Skylake SP Microarchitecture Changes

The net impact is that Intel expects a roughly 10% IPC improvement over Intel Xeon E5-2600 V4 cores (Broadwell-EP.) Our later benchmarking will show that at the same clock speed, we expect a >30% performance per clock improvement over Intel Xeon E5-2600 V1 cores (Sandy Bridge-EP.)

That is an important metric for two reasons. First, Intel Xeon E5-2600 V1 servers are those that will be hitting a 5-year refresh cycle with the Intel Xeon Scalable Processor Family generation. Second, that 30%+ IPC improvement is combined with a maximum core count increasing from 8 to 28 cores. This is the replacement cycle where consolidation can happen at an enormous scale. A general rule of thumb is that at the same clock speeds a three Skylake-SP chip will perform about equal to four Intel Xeon E5-2600 V1 cores.

Major Intel Xeon Scalable Processor Family L2 and L3 Cache Changes

If you compare the Skylake-SP core to a desktop Skylake core, you will notice that the L2 cache is much larger than the desktop counterpart. The server part has an additional 768KB of L2 cache for a total of 1MB L2 cache. Intel made this change in order to increase the amount of low latency data it has available to each core.

Intel Skylake SP Microarchitecture Major L2 And L3 Cache Changes

At the same time, Intel reduced the L3 cache by almost half from 2.5MB/core in Broadwell-EP to 1.375MB/core in Skylake-SP. That reduction helps Intel with transistor budget to increase the L2 cache size and core counts all on a 14nm process.

The question of why Intel would do this lies in cache latency. L2 cache is 3.5-4x faster than L3 cache. As core counts rise, L3 cache latencies rise so Intel needs to move more data closer to the CPU.

Intel Skylake SP Microarchitecture L2 L3 Cache Latency

One methodology Intel is using is to make the L3 cache non-inclusive. Here is Intel’s slide describing the difference and the process:

Intel Skylake SP Microarchitecture L3 Cache Inclusive V Non Inclusive

The key here is that instead of data being copied both to L2 and L3 caches, data can be loaded directly into the L2 cache. If you are a storage professional accustomed to storage tiering, this is roughly similar to being able to load data directly to an NVMe tier and then working with it and then pushing data, as it is less frequently used to a SATA/ SAS SSD tier or HDD tier instead of needing to copy it to both tiers before using it.

To be clear, the total cache size goes down with this design. L2+L3 on Broadwell-EP was 2.75MB while on Skylake-SP it is 2.375MB. The Broadwell-EP L3 cache has a copy of the L2 cache data so effectively it is a 2.5MB total cache.

Intel never gave us this view, but through a long presentation, but the extremely rough sketch of why this works looks something like this:

Intel Skylake SP V Broadwell SP Average Cache Latency Cumulative Capacity

Effectively since each core is able to get more low latency L2 cache, it can get big gains at capacities between 256KB and 1MB while giving up relatively little from 0-256KB and 1MB to 2.375MB. The final 128KB is the remaining delta in effective cache sizes.

That is a very rough diagram to illustrate the trade-off. The obvious other factor is that the shared L3 cache means that the higher latency data in Broadwell-EP’s L3 caches are available to other cores. With Skylake-SP there is not as much of this shared L3 cache data on the chip.

In practice, this means that combined with the Skylake-SP mesh improvements, most of the time Skylake-SP is faster, while sometimes Broadwell-EP is faster. Here is Intel’s data using SPECint_rate 2006 components:

Intel Skylake SP Microarchitecture L3 Cache Inclusive V Non Inclusive SPECint

Here is the SPECfp_rate 2006 version of that chart:

Intel Skylake SP Microarchitecture L3 Cache Inclusive V Non Inclusive SPECfp

Essentially what this data is telling us is that for SPECint and SPECfp workloads, having a larger L2 cache means that the probability of hitting low latency caches go up. It also tells us that for these workloads L3 cache misses are relatively similar even with the smaller inclusive L3 cache of Skylake-SP.

Read More

AMD EPYC 7642 Benchmarks and Review 48 Cores of Power



Leave a message